新聞中心

聯系我們
聯系我們

蘇州倍徠斯金屬材料制品有限公司

地 址:蘇州工業園區跨塘鎮唯和路93號A棟

聯系人:許志武 
手 機:188 6212 7231
聯系人:潘經理 
手 機:189 1260 8965
聯系人:許經理 
手 機:189 1260 8952


銷售辦:

總機:0512-6829 7075

傳真:0512-6823 6061

銷售處郵箱:jsblessed@163.com

產品詳細

31

產品名稱: 國產模具鋼Cr12MoV、4Cr5MoSiV1、9CrWMn等

發布日期: 2016-07-07

點擊數: 1855

二維碼:

簡述: 國產模具鋼Cr12MoV、4Cr5MoSiV1、9CrWMn等

產品詳情

國產模具鋼Cr12MoV、4Cr5MoSiV1、9CrWMn等

模具鋼Cr12MoV圓棒棒材材料 Cr12MoV鋼板材價格


合金工具鋼:Cr12MoV

適用范圍
冷作模具鋼,鋼的淬透性、淬火回火的硬度、耐磨性、強度均比Cr12高。用于制造截面較大、形狀復雜、工作條件繁重下的各種冷沖模具和工具,如沖孔凹模、切邊模、滾邊模、鋼板 深拉伸模、圓鋸、標準工具和量規、螺紋滾模等。

供貨狀態
供貨品種有熱軋材、鍛材、冷拉材、熱軋鋼板和冷拉鋼絲


化學成份:
碳 C :1.45~1.70
硅 Si:≤0.40
錳 Mn:≤0.40
硫 S :≤0.030
磷 P :≤0.030
鉻 Cr:11.00~12.50
鎳 Ni:允許殘余含量≤0.25
銅 Cu:允許殘余含量≤0.30
釩 V :0.15~0.30
鉬 Mo:0.40~0.60
力學性能:
硬度 :退火,255~207HB,壓痕直徑3.8~4.2mm;淬火,≥60HRC
Cr12MoV用途
Cr12MoV模具鋼淬透性、淬火回火后的硬度、強度、韌性比CR12高,直徑為300~400mm以下的工件可完全淬透,淬火變形小,但高溫塑性較差。Cr12MoV多用于制造截面較大、形狀復雜、工作負荷較重的合種模具和工具。如沖孔凹模、切邊模、滾邊模、鋼板等。
熱處理規范

熱處理規范:1.淬火,950~1000℃油冷;2.淬火1020℃,200℃回火2h。
金相組織:細粒狀珠光體+碳化物。
交貨狀態:鋼材以退火狀態交貨。

1)該鋼可用于制作材料厚度>3mm的沖裁模具復雜形狀的凸模、 凹模、鑲塊.制作凸模時建議硬度58~62HRC,制作凹模時建議硬度60 ~64HRC。
2) 用于制作沖裁模具中要求?耐磨的凸模、凹模。制作凸模時建議硬度為胍60~62HRC,制作凹模時建議硬度為62~64HRC。
3) 用于制作拉深模中要求耐拉的凹模,建議硬度為62 ~64HRC.
4) 用于制作彎曲模中要求耐磨、形狀復雜的凸模、凹模及鑲塊。制作凸模時建議硬度60~64HRC,制作凹模時議硬度60 ~64HRC

5) 用于制作鋁件冷擠壓摸的凸模、凹模。制作凸模時建議硬度60~62HRC,制作凹模時建議硬度62-64HRC。


公司主營產品有H13、P20、1.2344、430F、NAK80、718H、718、SKD11、SKD61、D2、SLD、LD、SKH-9、SKH-51、DF2、DIEVAR、1.2738、1.2316、1.2311、1.2083、1.2085、DC11、SKD3、6542、S136、GOA、cr12mov、4CR5MOSIV1、3cr2w8v、9crwmn、9SiCr、w6mo5cr4v2、w18cr4v、1.3343、M2、crwmn、SKS3、O1、1.2510、SKD12、D2、YXR3、DC53、cr12mo1v1、cr5mo1v、4cr13、420、7crsimnmov、S-STAR、M330、3cr17nimo、618、M300、8407、DH2F、FDAC、H11、1.2343等模具鋼產品,包括塑膠模具鋼、熱作模具鋼、冷作模具鋼、塑料模具鋼等。有模具鋼圓棒,鋼板、鋼帶、鋼卷、鋼管、六角鋼、扁鋼等型材,也可根據客戶要求加工各種鋼的型材。產品多樣,規格齊全,質優價廉。


Alloy tool steel: Cr12MoV
Applicable scope
Cold working die steel, steel quenching, quenching tempering hardness, wear resistance, strength are higher than Cr12. For manufacturing with large cross section, complex shapes and working conditions of heavy under cold stamping moulds and tools, such as punch, cut side mode, binding mode, steel plate deep drawing mode, circular saws, standard tools and gauge, thread rolling die and so on.
Supply status
Supply varieties of hot rolling, forging, cold drawn material, hot rolled steel and cold drawn steel wire
Chemical composition:
Carbon:1.45 C ~ 1.70
Si: Si = 0.40
Mn: Mn = 0.40
Sulfur: S = 0.030
P: P = 0.030
Chrome Cr:11.00 ~ 12.50
Ni Ni: allow residual content less than 0.25
Cu: allow residual copper content is less than 0.30
Vanadium:0.15 V ~ 0.30
Mo Mo:0.40 ~ 0.60
Mechanical properties:
Hardness: annealing, the indentation diameter 255 ~ 207HB, 3.8 ~ 4.2mm; quenching, more than 60HRC
Cr12MoV use
The hardness, strength and toughness of Cr12MoV die steel after quenching and tempering are higher than those of CR12. The diameter of the workpiece can be completely quenched, and the quenching distortion is small, but the high temperature plasticity is poor. Cr12MoV is used in the production of large cross section, complex shape, work load is more important in the mold and tool. Such as punching die, trimming die, die steel, piping etc..
Heat treatment specification
Heat treatment specification: 1 quenching, 950 ~ 1000 for oil cooling; 2 for quenching 1020, 200 for tempering 2h.
Metallographic structure: fine grained pearlite + carbide.
Delivery status: Steel in order to anneal state delivery.
1) the steel can be used to make the >3mm of the blanking die of the material thickness of the die, the concave die, the insert block. The proposed hardness 58~62HRC, when the production die, the proposed hardness of 60 ~64HRC.
2) punch, die wear-resisting requirements for the production of punching die in. The proposed hardness was 60~62HRC when the convex mold was made, and the hardness was 62~64HRC.
3) for the production of the drawing die, the hardness is 62 ~64HRC.
4) for the production of the bending die in the requirements of the complex, the shape of the convex mold, concave mold and insert block. When the production of convex die hardness of the proposed 60~64HRC, the production of die when the hardness of 60 ~64HRC
5) for the production of cold extrusion of aluminum parts of the convex die, die. It is suggested that the hardness of 60~62HRC is 62-64HRC when the convex die is produced.

 

版權所有:蘇州倍徠斯金屬材料制品有限公司 備案號:蘇ICP備15026697號

友情鏈接:蘇州倍徠斯金屬材料制品有限公司  蘇州倍徠斯金屬材料制品有限公司

1
許先生
3
潘經理
4
許經理
在線客服